Peak Power Meters for Crest Factor and Scalar Measurements Using Broadband OFDM Signals
Posted May 1, 2015By Vitali Penso, Boonton Electronics
In this application note we highlight how broadband LTE and WiFi power amplifier (PA) performance can be characterized using Boonton’s high performance USB peak power meter. Figure of merit measurements like input and output crest factor can be performed to characterize amplifier compression using highly dynamic and broadband LTE & WiFi signals. With the use of a directional coupler the USB peak power meter is transformed to make scalar-like measurements such as gain and return loss.
Crest Factor and Scalar–Like Measurements Using Modulated Broadband Signals for Power Amplifiers
A critical component of a base station is the power amplifier (PA). Over the past two decades the PA has experienced monumental changes in its architecture and performance. Two significant improvements have been in power-added efficiency & bandwidth. Fifteen years ago a 2G base station PA housed in a ground base station cabinet would output 5 MHz multi carrier CDMA signals at 40W; running at 5% efficiency it would generate 760 Watts of heat, taking up a significant amount of space, power and cooling resources and costing thousands of dollars. Today’s 4G amplifiers using Doherty architecture with predistortion has improved the efficiency of an amplifier to over 35%, significantly reducing the size and enabling integration of the PA with the transceiver and the duplexer into a remote radio head (RRH) placed near the antenna.
The other significant improvement has been in PA bandwidth. Today’s RRHs are deployed in systems where the carriers are placed anywhere in a 70 MHz (or wider) frequency band. Measuring and characterizing the performance of the wideband PA requires test equipment that supports the bandwidths used in today’s deployments. In this application note we show how using Boonton’s high performance peak power meters with directional couplers enable the designer to make input, output and reflected power measurements; facilitating scalar analyzer like measurements such as gain and input return loss using multi-carrier, wide bandwidth (>100 MHz) test signals as opposed to narrowband CW. The statistical analysis tool of the peak power meter provides insight into the amplifier compression by measuring and comparing crest factor of input and output signals of the PA using wideband 4G signals while monitoring both peak and average power.
Measuring PA Compression & Crest Factor In an ideal world the PA output signal is an amplified version of the input signal; input power plotted vs output power produces a straight linear line, where the slope of the line is 1. In reality however, as the PA is driven harder, at a certain point the output will not increase as much as the input power; at this point the amplifier is in its non-linear region or is in compression. In the non-linear region the PA generates intermodulation products (Figure 2a
) which cause emission of spurious power into adjacent channels. Aside from affecting adjacent channels, non-linearity also degrades EVM of the desired signal which causes loss of signal quality. In wireless communication systems modulation schemes such as CDMA (2G), WCDMA (3G), QAM and OFDM (4G-LTE) the signal is highly dynamic where 10 dB crest factor or peak to average power ratio (PAPR) is not unusual. When the amplifier goes into compression driven by a CDMA or OFDM modulated wideband signal, rare occurring peaks get compressed first; so when an amplifier is in 0.2 dB average power compression, its peak can be compressed by 1.0 dB or more. For example, a PA with 40 dB gain, 0 dBm average input signal with a crest factor of 10 dB (peak 10 dBm) would output 39.8 dBm average power but the peak power would be clipped at 49 dBm (crest factor 9.2 dB). While average (true RMS) power meters measure the average power of the signal, they lack the bandwidth to capture the peaks, whereas Boonton’s 55 series USB peak power meter in a dual channel configuration can accurately measure both input and output average and peak power in real-time. With statistical analysis capability the 55 series can display the statistical distribution of the signal power level relative to its average power in a format called complementary cumulative distribution function (CCDF). CCDF can give significant insight into the behavior of the PA as it is driven harder into saturation by measuring changes is in PAR and crest factor of the input and output signals simultaneously and providing a graphical view of the compression of the amplifier in real-time (Figure 2b
Performing Scalar Analyzer–Like Measurements–Gain & Input Return Loss
shows a typical PA test set-up using peak power meters and a bidirectional coupler to make scalar analyzer like measurements such as gain and return loss. The input power is measured coupling off the input signal to the amplifier by using a bi-directional coupler. The reflected power from the input of the amplifier can be measured using the reverse coupling port of the same bi-directional coupler. Since the typical average power rating of a power meter is about +20 dBm, the output of the PA is attenuated to protect the power sensor while making output power measurements. It is important to note that the bi-directional coupler needs to have excellent directivity.
Before measurements can be taken a basic calibration procedure is required at the frequencies in which the amplifier is going to be tested; all unused ports of the coupler need to be terminated with 50 ohms while making measurements.
L1: Loss from LTE Generator output to the FWD port of the bi-directional coupler
L2: Loss from LTE Generator output to the power amplifier input
L3: Loss from amplifier output to the 40 dB attenuator output
L4: Loss from amplifier input into the REV port of the bi-directional coupler
Once the losses are measured, input, output and reflected power measurements can be made:
P1: Power reading at FWD port of the bidirectional coupler
PA input power = P1+L1-L2
P2: Power measured at the 40 dB attenuator output
PA output power=P2+L3
P3: Power measured at REV port of the bidirectional coupler PA input reflected power=P3+L4 The input, output and reflected power measurements can be used to compute gain (S21) and input return loss (S11)
PA Gain(dB)=PA output power(dBm)–PA input power (dBm)
PA input return loss(dB)=PA input power(dBm)–PA input reflected power(dBm)
For example average input power of 0 dBm and output power of 46 dBm would mean 46 dB gain and average reflected power of -10 dBm would be 10 dB input return loss. Making the measurements in statistical mode provides average power and peak power of all three measurements (input, output and reflected power). Reading average and peak power simultaneously allows monitoring amplifier compression and making crest factor measurements that were described previously.
Boonton Peak Power Meter Solutions Measuring peak power & crest factor of multi-carrier LTE signals (70+ MHz) as well as 802.11ac Wifi signals (160 MHz) requires wide bandwidth peak power meters. Boonton’s 55006 USB peak power sensor with 195 MHz video bandwidth can handle the challenging LTE and WiFi 802.11ac signals. 55006 GUI supports up to 8 channel measurements which is more than what is covered in this application note for scalar-like measurements. In statistical mode with sampling speed of 100 million points (samples) per second, crest factor measurements converge rapidly. While the high performance of the sensor makes it well suited for R&D, 100,000 triggered measurements per second also makes it the fastest sensor to use in manufacturing. Affordability allows quality engineers to use the same model sensor used in R&D in verification. The small form factor enables field engineers to use the same R&D equipment in the field for measurements that correlate well with the lab measurements.